Den sista är beroende på att jag inte har ett CanalDigital kort ännu och den USB-porten är inte i drift. Man behöver väl inte ha båda igång då jag har satt # framför den CWS:en

#CWS = 127.0.0.1 10000 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserv
CWS = 192.168.0.5 10001 peter peter 14 02 03 04 05 06 07 08 09 10 11 12 13 01 lan cardserv

Sen det andra Config-felet du markerade, är det beroende på att jag har 10000 och 10001 skiftade tro? Har provat att byta plats och startat om men det funkar inte. Vilket interface rekomenderas? Kör med MG 1.24 i dreamboxen.

Så här ser puttyfieln ut nu...


[ 20:16:05 ] [ Box detect ] Box type 1
[ 20:16:05 ] [ Config ] Enabling SSL engine
[ 20:16:05 ] [ Config ] SSL engine disabled due to Certificate errors
[ 20:16:05 ] [ Config ] Option <Seca-PPV> for device 0 (Canal Anal) not present, defaulting to NO
[ 20:16:05 ] [ Config ] /dev/ttyUSB1 ECM priority: round
[ 20:16:05 ] [ Config ] Option <Seca-PPV> for device 1 (ViaSpratt) not present, defaulting to NO
[ 20:16:05 ] [ Config ] Value in <boxkey> for device 1 (ViaSpratt) is INVALID, skipping...
[ 20:16:05 ] [ Config ] /dev/ttyUSB0 ECM priority: round
[ 20:16:05 ] [ Config ] Option <spider> not present for User: peter, defaulting to NO
[ 20:16:05 ] [ EMM Cache ] Initialising Cache with 10 entries
[ 20:16:05 ] [ ECM Cache ] Initialising Cache with 10 entries
[ NewCS ] Process ID is: 2336
[ 20:16:05 ] [ Loader ] Starting Telnet on port 7806
[ 20:16:05 ] [ Loader ] Reader type 2 on node /dev/ttyUSB1
[ 20:16:05 ] [ Phoenix ] Opening device /dev/ttyUSB1
[ 20:16:05 ] bind: error! 98: Address already in use
[ 20:16:05 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:16:05 ] [ Phoenix ] Setting 2 Stop bits on node /dev/ttyUSB1
[ 20:16:05 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:16:05 ] [ Phoenix ] Normal RESET on node /dev/ttyUSB1
[ 20:16:07 ] [ ATR ] T=0 1etu=104.17us Guardtime:15etu WWT:9600etu[ 20:16:07 ] [ ATR ] Historical bytes: 3 [B0] [09] i [FF] J P p [00] [00] V T [01] [00] [00]
[ 20:16:07 ] [ Loader ] Init NDS card
[ 20:16:07 ] [ Phoenix ] Setting Parity to: ODD
[ 20:16:07 ] [ Phoenix ] Setting 2 Stop bits on node /dev/ttyUSB1
[ 20:16:07 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:16:08 ] [ Keyman ] Adding key 59767793 type 0 on Provider 000000 for caid 090F ID=0
[ 20:16:08 ] [ Keyman ] Adding key 59767700 type 1 on Provider 000000 for caid 090F ID=0
[ 20:16:10 ] [ Loader ] Card 090F on port /dev/ttyUSB1 ready
[ 20:16:10 ] [ Loader ] Starting Newcamd Server on port 10001
[ 20:16:10 ] [ Loader ] Reader type 2 on node /dev/ttyUSB0
[ 20:16:10 ] [ Phoenix ] Opening device /dev/ttyUSB0
[ 20:16:10 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:16:10 ] [ Phoenix ] Setting 2 Stop bits on node /dev/ttyUSB0
[ 20:16:10 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:16:10 ] bind: error! 98: Address already in use
[ 20:16:10 ] [ Phoenix ] Normal RESET on node /dev/ttyUSB0
[ 20:16:12 ] [ Loader ] Reset failed ...
[ 20:16:12 ] [ Loader ] Starting Newcamd Server on port 10000
[ 20:16:12 ] bind: error! 98: Address already in use
[ 20:16:12 ] [ NewCS ] Ready to GO!



Känns som att man blandar ihop allt hela tiden, men som jag förstått så är det iaf viktigt att starta om MGcamd filen i dreamboxen efter varje ändring och att man startar om kortet i putty.

Har provat att byta portar men verkar inte funka...

Nästa steg?