Matrix Reloaded

[Cue_]

Är det nån som vet hur man programerar en sån ? ...det ska visst gå att programmera det med ett par funcards stämmer det?

Finns det nån tutorial/guide som jag kan följa eller nåt ?

[admin]

Programmera en Matrix Reloaded?!?!?! :shock:

[T-bird]

Har inte sett några guider, det ställe som har mest info om MR är nog Toecutter http://66.135.34.88/~takula/forum//index.php?s=

Ska gå fint att progga med fun, men dom ska vara stora tror att det är 2st fun6 som går åt

[Cue_]

OK tack ..men om jag bara skickar över PentaCrypt till den räcker det då för att köra ett funcard med viasat ?

[admin]

Någon som kan förklara vad det är?
Jag vet inte vad det är.. vill gärna veta

[T-bird]

Kan tyvär inte säga vad man kan eller inte kan
Jag vet helt enkelt för lite om dom :cry:

[Cue_]

Någon som kan förklara vad det är?
Jag vet inte vad det är.. vill gärna veta

Det är en modul som Magic Module. Och den ska vara bättre är vanliga Matrix Module
Ska klara penta 1,09

[Cue_]

Kan tyvär inte säga vad man kan eller inte kan
Jag vet helt enkelt för lite om dom :cry:

vet du hur man gör för någon annan module (kanske är på sammasätt)

[T-bird]

Jag var över till Toecutter och tog detta från en Sticky

Tror nog att du skulle regga dig och ta dig tid att läsa där för det finns hur mycket som helst och allt verkar inte så solkart hur det fungerar

HOW TO UPDATE USING FUNCARDS
For the ones that don't know how to update, i got this from AHAC.
Thanks M8

Programing Matrix Reloaded ( MR ) for dummies by ahac

For all the dummies like me that also have probs programming the MR Matrix Reloaded the first time:

From many posts here I understand the best it goes with fun5 cards, e.g. Galaxy3 cards.

You'll need 3 of them, or with one it works also, you only have to reprogram it.

Get yourself the zip file of the FW (today it is the version 1.03)

When you open the zip you'll find several files, unzip them all to a Map (make a new one, you can find easily later on) In my case I'll call it MR103.

In the M103 file map you now see 2 files one "fun 5"and one "fun6"

Put you're funcard in the programmer, like Mastera, Infinity, Mastercard etc. and erase it.

Open the program you normaly use to write files on a funcard.
Some people say ChipCat will not work.
Erase the funcard.

Load the flash file (from the map MR103 > fun5) in that section.
Load the file mr103_512_11.hex in the external eeprom section en write the card.

Go to the setup of your receiver and open the section where the Common Interfase module is.

1- Open the MR section and go to Download section.
(Can't describe the real name, çause that's depending from your receiver)
2- The messages "Erasing old data, please wait..." and "Insert card 1 or serial dummy card" will be shown.
3- Insert the first smart card and press Ok.
4- The message "Card inserted, opening" is shown, and after that "Performing smart card download..." and wait until
5- the message "Download card completed" appears take the card out and press "Please, extract it"
6- After that, a message "Insert card 2" will be shown.

Follow the options as above until the last card has finished downloading using the eeprom file mr103_512_21.hex for card number 2 and mr103_512_31.hex for card number 3.

7.- After the last smart card is downloaded, the message "Download complete. Copying image and re-booting" will be shown. Just wait a few moments.

If the new version of software is not shown after about 1 minute, re-insert the module without any smartcard.

When this also doesn't work, completely shut off the receiver once.

Notice: If you're zapping the first time, do not insert any card.
If some decoded channels could be watched, it works fine.

Have fun!

If one of the Funcards isn't directly detected, please try inserting this card some time, or rewrite it!
Don't panic!


REPLACE THE MR1.03 BY MR 1.04

Thank you goes to AHAC for writing this post.

Cheers,

Cor.

************************************************** ***********************************************
************************************************** ***********************************************

I have mentioned it over a dozen times now on the forums so here it is in a sticky

my recent tests on the MR indicate that all operations should be done AFTER puting the cam on an FTA channel , going to standby and back on again and being on the same fta channel

this reboots the cam and its not being accessed because there is nothing to decrypt

then make your changes , save if possible and exit

if you do not do this then any tests are meaningless

this also applies if reprogramming with funcards or a mutznutz

[Cue_]

ok ska läsa igenom ...tack för hjälpen